BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / BRAKES

Brake fluid flush and bleeding

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory hydraulic brakes. Use the procedure for the installed ABS or non-ABS system.

IntermediateReplacement steps45–90 minSOURCE-BASED GUIDESource references recorded · technical review pending

Brake fluid flush and bleeding

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory hydraulic brakes. Use the procedure for the installed ABS or non-ABS system.

Tools

  • 7 mm or 9 mm six-point bleeder wrench, according to the fitted screw.
  • Reservoir pressure bleeder, clear hose, catch bottle and low-range torque wrench.

Tightening & service specifications

Bleeder screw with a 7 mm wrench size
5 NmBMW E30 torque manual · 34-1 · PDF 136
Bleeder screw with a 9 mm wrench size
6 NmBMW E30 torque manual · 34-1 · PDF 136
Maximum reservoir bleeder pressure
2 barFollow the bleeder and factory instructions for the ABS or non-ABS procedure.BMW · 34-2
Replacement steps

Before you start

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory hydraulic brakes. Use the procedure for the installed ABS or non-ABS system.

Estimated time
45–90 minPlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • 7 mm or 9 mm six-point bleeder wrench, according to the fitted screw.
  • Reservoir pressure bleeder, clear hose, catch bottle and low-range torque wrench.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Fresh approved brake fluid in a sealed container.

Manual references

34-2 · 34 00 046 / 047

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Chock the wheels and support the car on rated stands or a lift before removing a wheel. A jack alone is insufficient.
  • Pump the pedal until firm before moving the car. Stop if the pedal sinks, a leak appears or the brakes drag.
  • Brake fluid damages paint. Do not let the reservoir run dry or exceed the pressure limit.

Walkthrough

Identify ABS and prepare the bleeder

Use the fresh fluid specified for the installed brake system. Connect a reservoir pressure bleeder with a sound cap gasket. BMW gives a 2 bar maximum for the pressure equipment on this page.

Check: The bleeder holds pressure without leaks and the reservoir stays supplied.

Bleed in the correct sequence

For ABS, follow 34 00 047. Start at the right rear, then left rear, right front and left front. At each wheel, hold the pedal down and open the bleeder. Release the pedal and stroke it fully 12 times. Hold it down, close the bleeder, then release the pedal. For conventional brakes, use 34 00 046 and close each bleeder when the fluid is clear of air.

Check: Fresh, bubble-free fluid emerges from each bleed hose.

Close the bleeders and check

Tighten a 7 mm wrench-size bleeder to 5 Nm or a 9 mm one to 6 Nm. Release bleeder pressure before removing the cap, set the reservoir level and check at all four wheels.

Check: No fluid leaks and a held pedal stays firm.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

34-2 · 34 00 046 / 047 · PDF pages 641

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory hydraulic brakes. Use the procedure for the installed ABS or non-ABS system.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.