BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / SUSPENSION

Front strut, upper mount and damper

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Check the damper and upper mount type before applying shaft torque.

AdvancedReplacement steps2–4 hr per sideSOURCE-BASED GUIDESource references recorded · technical review pending

Front strut, upper mount and damper

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Check the damper and upper mount type before applying shaft torque.

Support the strut and use a spring compressor that fits the spring. Never loosen the center nut while the spring is loaded.

Tools

  • BMW 31 3 111 spring compressor with the fitting shown, and 31 3 170 shaft-nut tool with a counterhold.
  • BMW 31 3 150 or 31 3 180 retaining-ring tool, according to the installed collar.

Tightening & service specifications

Upper mount to body
22 NmReplace the self-locking nuts.BMW E30 torque manual · 31-7 · PDF 107
Damper shaft nut, original M12 external hex shaft
64 NmBMW E30 torque manual · 31-7 · PDF 107
Damper shaft nut, original M12 internal hex shaft
44 NmBMW E30 torque manual · 31-7 · PDF 107
Original damper retaining collar
130 NmCheck replacement damper instructions if the supplied ring differs.BMW E30 torque manual · 31-8 · PDF 108

BMW catalog parts

1991 325i coupe · front strut and damper diagram

Replacement steps

Before you start

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Check the damper and upper mount type before applying shaft torque.

Estimated time
2–4 hr per sidePlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • BMW 31 3 111 spring compressor with the fitting shown, and 31 3 170 shaft-nut tool with a counterhold.
  • BMW 31 3 150 or 31 3 180 retaining-ring tool, according to the installed collar.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Matched strut inserts or mount components as required and new upper-mount locking nuts.

Manual references

31-11 to 31-14 · 31 31 000 / 31 32 001

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Chock the wheels and support the car on rated stands or a lift before removing a wheel. A jack alone is insufficient.
  • Never release the shaft nut while the spring bears on the mount. Use a compressor with the correct hooks for the spring.

Walkthrough

Remove the strut assembly

Support the hub and brake caliper. Disconnect the links shown on page 31-11 and clear the hose and sensor leads before releasing the top mount.

Check: The assembly comes out without pulling on brake or sensor lines.

Unload the upper mount

Check the parts order on 31-12. Fit BMW 31 3 111 or a correctly sized equivalent and compress the spring until it is free of the mount. Counterhold the shaft with the tool specified for its head.

Check: The compressor is seated securely and the spring is unloaded at its ends.

Replace the insert or upper mount

Use the established collar tool for the cartridge. Assemble the isolators, spring and mount in BMW’s order. Select the shaft-nut torque using the actual internal or external hex design from the specification card.

Check: The spring ends are in their seats before the compressor is removed.

Install and check alignment

Install the complete strut with new locking nuts at the upper body mount and tighten them to 22 Nm. Use the linked front axle specifications for the joints disturbed during removal. Restore hose support and have alignment checked.

Check: Steering moves freely with no contact or tension on the leads.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

31-11 to 31-14 · 31 31 000 / 31 32 001 · PDF pages 516, 519, 520, 521

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Check the damper and upper mount type before applying shaft torque.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.