BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / ENGINE

M20 spark plugs

E30 325i with the original M20 and factory-type M14 × 1.25 plugs. Install six of the same type.

BeginnerReplacement steps30–60 minSOURCE-BASED GUIDESource references recorded · technical review pending

M20 spark plugs

E30 325i with the original M20 and factory-type M14 × 1.25 plugs. Install six of the same type.

Tools

  • 21 mm (13/16 in nominal) spark plug socket for the listed Bosch W-series plugs.
  • 20.8 mm (13/16 in) deep spark plug socket for NGK ZGR5A.
  • BMW 12 1 180 plug-lead pliers for original connectors. Pull by the boot.

Tightening & service specifications

Original-type M14 × 1.25 spark plug
30 ± 3 NmUngreased, per BMW TIS. Follow the exact replacement plug’s installation instructions.
BMW-listed Bosch plug gap
0.7–0.8 mmFor the adjustable Bosch plug listed in the BMW application chart.BMW spark plug application chart

BMW catalog parts

1991 325i sedan · ignition wiring diagram

Replacement steps

Before you start

E30 325i with the original M20 and factory-type M14 × 1.25 plugs. Install six of the same type.

Estimated time
30–60 minPlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • 21 mm (13/16 in nominal) spark plug socket for the listed Bosch W-series plugs.
  • 20.8 mm (13/16 in) deep spark plug socket for NGK ZGR5A.
  • BMW 12 1 180 plug-lead pliers for original connectors. Pull by the boot.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Six identical spark plugs approved for the installed M20.

Manual references

12 12 · M20 ignition wires and spark plugs

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Let the engine cool before working around the plugs, fan or exhaust.
  • Work on one lead at a time. Start the new plug by hand to protect the head threads.

Walkthrough

Identify the plug and socket

Match the factory application before opening the plug boxes. Use a 21 mm deep spark plug socket for the listed Bosch W-series plugs or 20.8 mm (13/16 in) for NGK ZGR5A. Check the gap only where the plug maker permits adjustment.

Check: All six plugs are the same approved type.

Remove and inspect

Pull each connector by its boot with the specified plug-lead pliers. Clear grit from around the plug before removing it. Record the condition by cylinder if the old plugs show unusual deposits.

Check: The plug holes are clean and the leads remain in firing order.

Install and check

Install the plugs by hand, then tighten the clean, dry factory-type M14 plugs to 30 ± 3 Nm, subject to the replacement plug’s installation instructions. Refit the connector fully and check for a smooth idle after all six are installed.

Check: Every boot is seated and the engine runs evenly.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

12 12 · M20 ignition wires and spark plugs

E30 325i with the original M20 and factory-type M14 × 1.25 plugs. Install six of the same type.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.