BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / BRAKES

Rear brake pads and discs

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory rear discs and the capped guide bolts in BMW’s illustration.

IntermediateReplacement steps1–2 hr per axleSOURCE-BASED GUIDESource references recorded · technical review pending

Rear brake pads and discs

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory rear discs and the capped guide bolts in BMW’s illustration.

Tools

  • 7 mm hex bit for the factory rear guide bolts.
  • Disc micrometer, caliper hanger, rated stands and torque wrench.

Tightening & service specifications

Rear disc retaining screw
16 NmBMW E30 torque manual · 34-2 · PDF 137
Rear caliper carrier to trailing arm
67 NmBMW E30 torque manual · 34-2 · PDF 137
Original 7 mm hex rear guide bolts
30 Nm, −5 Nm toleranceBMW E30 torque manual · 34-2 · PDF 137

BMW catalog parts

1991 325i coupe · rear brake diagram

Replacement steps

Before you start

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory rear discs and the capped guide bolts in BMW’s illustration.

Estimated time
1–2 hr per axlePlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • 7 mm hex bit for the factory rear guide bolts.
  • Disc micrometer, caliper hanger, rated stands and torque wrench.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Matched rear pad set.
  • Two matching discs if the discs are being replaced.

Manual references

34-8 to 34-9 · rear pads and discs

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Chock the wheels and support the car on rated stands or a lift before removing a wheel. A jack alone is insufficient.
  • Keep grease off the disc and lining. Support the caliper independently of its hose.
  • Pump the pedal until firm before moving the car. Stop if the pedal sinks, a leak appears or the brakes drag.
  • Chock the car independently of the parking brake. Release that brake before removing the rear discs.

Walkthrough

Remove the pads

Remove the caps and use a 7 mm hex bit on the original guide bolts. Hang the caliper. Note the positions of the pads and retaining spring.

Check: The rear caliper is supported and the pads match the replacements.

Fit the rear discs

Remove the carrier and retaining screw. Back off the parking brake shoe adjuster if the disc will not release. Clean the hub face and inspect the shoe linings before seating the new disc.

Check: The disc seats flat and the parking brake shoes stay in place.

Refit and check

Tighten the disc screw to 16 Nm, the carrier to 67 Nm and the original 7 mm guide bolts to 30 Nm with −5 Nm tolerance. Restore the parking brake adjustment and pump the service pedal before driving.

Check: Both discs turn freely with the brake released and hold when applied.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

34-8 to 34-9 · rear pads and discs · PDF pages 647, 649

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory rear discs and the capped guide bolts in BMW’s illustration.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.