BMW E34 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / ENGINE

Replace the M50 valve-cover gasket

Reseal the factory cam cover and spark plug wells while preserving coil grounds, cover seals and the specified joint treatment.

IntermediateReplacement steps1–3 hoursSOURCE-BASED GUIDESource references recorded · technical review pending

M50 and M50TU valve cover gasket

U.S. E34 525i with the original M50 or M50TU. Confirm the cover and production split at September 1992.

Tools

  • Low-range torque wrench. Check the actual cover fasteners and the coil/ground fasteners before choosing sockets.

Tightening & service specifications

Original M6 valve-cover hardware
10 NmFor the cover-to-head fasteners.Bentley · 116-4, gasket and cover installation

BMW catalog parts

1995 525i sedan · valve cover diagram

Replacement steps

Before you start

Bentley-covered E34 525i with an original M50/M50TU head and cover. Verify the gasket kit, cover type and applicable sealing points. Oil from above the cover or a damaged cover needs a separate repair.

Estimated time
1–3 hoursEditorial estimate for an accessible, source-matching installation.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • Light and inspection mirror
  • Lint-free cloths
  • Socket set and ratchet
  • Straight extension
  • Camera or labels
  • Non-marring scraper
  • Low-range torque wrench

Check sizes and special fixtures for the installed hardware.

Required parts

  • Matching perimeter gasket
  • Matching plug-well seals
Parts to inspect or match separately
  • Correct fastener insulators/grommets if deteriorated or required by the selected kit instructions
  • Breather fitting/connector or cover only if damage is found
  • Sealant only at locations and cure conditions specified for the actual gasket/cover product

Stop the job if

  • Wrong/uncertain cover or kit
  • Cracked/distorted cover or damaged mating face
  • Brittle fitting that cannot release normally
  • Unremoved fastener or force required to lift cover
  • Missing ground/bracket/hardware record
  • Gasket will not remain seated
  • Continued oil leak or abnormal running

Manual references

116-3–116-4, M50 cylinder head cover

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Work cold with the battery isolated according to the vehicle procedure. Keep tools, old gasket and solvent clear of exposed valve gear.
  • A gasket cannot correct a distorted cover or a damaged sealing face.

Walkthrough

Verify the leak and gather matching seals

Tools: Light and inspection mirror · Lint-free cloths

Manual 116-3 ↗

Clean the suspected area and trace fresh oil. Identify the perimeter seal, plug-well seals and fastener insulators against the actual cover before disassembly.

Check: The leak points to the cover joint or plug wells and the kit fits the cover.

Disconnect cover attachments

Tools: Socket set and ratchet · Straight extension · Camera or labels

Manual 116-3 ↗

Remove the covers and ignition coils. Photograph the ground straps and their studs, release the breather at its fitting, and move the wiring aside with support. Record fastener insulator placement.

Check: The harness, grounds and breather are free without breaking a fitting.

Lift the cover and prepare the mating surfaces

Tools: Socket set and ratchet · Non-marring scraper · Lint-free cloths

Manual 116-4 ↗

Lift the cover evenly and remove the seals. Inspect the cover, plug-well grooves and head joints. Use a non-marring tool and keep old sealant out of the head. Clean and dry the sealing faces.

Check: The groove and surfaces are clean, with no cracks or damaged sealing edge.

Install seals and seat the cover

Tools: Light and inspection mirror

Manual 116-4 ↗

Install the perimeter and well seals without stretching. Use sealant only where the gasket or vehicle instructions specify it. Lower the cover squarely and verify that the rear gasket contour and well seals stay seated.

Check: The gasket remains in the groove all the way around and no wire is trapped.

Tighten and confirm the repair

Tools: Low-range torque wrench · Socket set and ratchet · Light and inspection mirror

Manual 116-4 ↗

Refit the insulators and tighten the source-matching cover hardware progressively and evenly to the listed 10 Nm. Restore every ground, coil and breather connection. Observe any sealant cure interval, then check the perimeter and wells for fresh oil and recheck after a heat cycle.

Check: The engine runs normally and the repaired seam stays dry.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW 5 Series (E34) Service Manual

116-3–116-4, M50 cylinder head cover · PDF pages 101, 102

Bentley-covered E34 525i with an original M50/M50TU head and cover. Verify the gasket kit, cover type and applicable sealing points. Oil from above the cover or a damaged cover needs a separate repair.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.