Use this source with your vehicle record
U.S. models: 525i 1989-1995; 535i 1989-1993; 530i and 540i 1994-1995. Applicability within each chapter still varies.
Match the installed engine, production period and relevant equipment before using a source procedure. The links below connect the chapter to current reference content and member experience.
Jobs in this chapter
Open each repair job for linked DIY guides, owner walkthroughs and comments. The locator points to the start of the topic in your service manual.
- Radiator, reservoir and fan arrangement170-1 · PDF p. 205Guides & owner fixes
- Cold cooling-system pressure test170-2 · PDF p. 206Guides & owner fixes
- Thermostat, temperature gauge and fan checks170-3 · PDF p. 207Guides & owner fixes
- Auxiliary fan temperature switch170-4 · PDF p. 208Guides & owner fixes
- Coolant draining, filling and bleeding170-5 · PDF p. 209Guides & owner fixes
- M20 water pump replacement170-6 · PDF p. 210Guides & owner fixes
- M30 water pump replacement170-7 · PDF p. 211Guides & owner fixes
- M50 water pump replacement planning170-8 · PDF p. 212Guides & owner fixes
- M60 water pump replacement170-9 · PDF p. 213Guides & owner fixes
- Thermostat replacement170-10 · PDF p. 214Guides & owner fixes
- Radiator removal and installation170-11 · PDF p. 215Guides & owner fixes
- Mechanical cooling fan replacement170-12 · PDF p. 216Guides & owner fixes
Walkthroughs from these pages
All walkthroughs ↗Start an overheating investigation with a cold inspection
Create a useful first record of coolant loss, belt condition, hoses and radiator airflow before treating a suspected component as a confirmed failure.
170-1 to 170-2 · inspection · source-based guideSeparate an airflow concern from a fan diagnosis
Understand the mechanical fan and auxiliary electric fan, then gather cold, engine-off observations useful for an overheating-at-idle question.
170-1; 170-3 · inspection · source-based guidePlan an M50 coolant-pump job
Check the parts and bleed procedure first, then follow the source-checked mechanical sequence for fan access, pump extraction, seal installation and even tightening.
170-8–170-9, Figs. 12–13; 170-12; 020-13 · planning · source-based guideReplace the M20 timing belt and tensioner
Expose the factory belt drive, establish cylinder 1 TDC, install the belt with slack at the tensioner and verify the marks through two turns.
118-1–118-4, Figs. 1–8; 170-5 · replacement · source-based guidePlan an S52 swap into an M50 E34 525i
Build the recipient-to-donor fitment sheet for sump clearance, cooling, wiring, emissions and first start before buying or removing an engine.
100-1–100-4; 110-4–110-8; 119-5; 130-20; 170; 200-2 · build planning · source-based guidePlan an M60B30 to M60B40 engine swap
Compare an E34 530i recipient to the factory E34 540i package and account for the larger engine’s drivetrain, cooling and management requirements.
100-1, Table a; 110-12–110-14; 170-9; 200-1–200-2 · build planning · source-based guidePlan a mechanical fan delete with electric cooling
Treat the electric fan, shroud, relay circuit and failure behavior as a cooling system, with measurable hot-idle checks before road use.
170-1–170-4, 170-12; 600-4; 610-1–610-5 · build planning · source-based guideDrawings and component references
Browse illustrated OEM catalogChapter discussions
No discussions linked to this chapter yet. Ask with the car’s configuration and exact source page so other owners can follow the same reference.