BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / ENGINE

M20 oil and filter change preparation

Match the filter and drain hardware, then find the factory fill quantities and service checks.

BeginnerReference15–25 min preparationSOURCE-BASED GUIDESource references recorded · technical review pending

M20 oil and filter service

1991 U.S. 325i coupe, M20, rear-wheel drive. Check the sump and the spin-on filter installed on the car.

BMW’s two references disagree on the sump plug. Confirm the applicable specification for your sump and plug before starting.

Tools

  • 17 mm six-point socket for the original BMW 11 13 1 273 093 drain plug; check the head on a replacement.
  • Strap wrench for filter removal; MANN W 719/15 is 76 mm outside diameter.

Tightening & service specifications

Spin-on filter
Hand-tighten per the filter instructionsUse the filter maker’s seal-contact and turn instructions.
Oil fill with new filter
4.25 LUse the dipstick for final level.BMW 325i / 325is handbook · p. 84 (PDF 85)
M12 × 1.5 sump plug
Check the specification for the fitted sumpThe archived torque manual lists 35 Nm; the later BMW TIS table lists 25 Nm. Confirm which applies before tightening.BMW E30 torque manual · 11-10 · PDF 11

BMW catalog parts

1991 325i coupe · oil filter diagram

Reference

Before you start

US 325i / 325is M20 handbook figures. Identify the installed sump and filter, especially on a swapped engine.

Estimated time
15–25 min preparationTime to identify the fitted hardware and gather supplies. Drain and refill time varies.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • 17 mm six-point socket for the listed BMW 11 13 1 273 093 plug
  • Strap-type oil filter wrench that fits the installed canister (76 mm outside diameter for MANN W 719/15)
  • Torque wrench that covers the installed plug specification
  • Drain pan of at least 5 L
  • Funnel
  • Gloves and eye protection

Check sizes and special fixtures for the installed hardware.

Required parts

  • Engine oil to the applicable BMW specification
  • Matched spin-on oil filter
  • New drain plug sealing washer
Parts to inspect or match separately
  • Replacement plug if the head, threads or sealing face are damaged

Stop the job if

  • The sump or drain plug differs from the catalog and you cannot establish the matching specification.
  • The plug turns without tightening, or the old filter seal has not come off with the old filter.

Manual references

00-15 · Engine oil service, operation 00 00 249

Use these page numbers in your copy of the manual.

SWG catalog · 17 mm hex for BMW 11 13 1 273 093 ↗

MANN W 719/15 size and fitment ↗

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Use level ground for the final oil reading and rated supports if access requires lifting.
  • Avoid hot oil. Check plug thread and tightening specification against the installed sump.

Reference checks

Identify the service parts

Tools: 17 mm six-point socket for the listed BMW 11 13 1 273 093 plug · Strap-type oil filter wrench that fits the installed canister (76 mm outside diameter for MANN W 719/15)

Manual 00-15 ↗

Compare the fitted filter, drain plug and seal against the two catalog drawings. The listed M12 × 1.5 BMW plug takes a 17 mm socket. Check replacement plug heads and filter canister dimensions before choosing a tool.

Check: The socket seats fully and the filter, drain plug and new seal match the installed parts.

Check the handbook fill amount

Tools: Drain pan of at least 5 L · Funnel

Manual Handbook p. 84 ↗

The 325i handbook lists 4.25 L with the filter changed, or 4.0 L without. Confirm the procedure for the installed sump and use the dipstick for the final level.

Check: You have enough oil and a way to verify the level.

Plan the final checks

Tools: Gloves and eye protection

Manual 00-15 ↗

After following the service procedure, check for leaks at the filter and drain plug. On level ground, allow oil to drain back and recheck the dipstick. Take used oil and the filter to an approved collection point.

Check: The level is in range and the filter and drain plug stay dry.

Record your findings

Keep observations and unresolved questions in your private journal before deciding on a repair.

Add to My garage ↗
BMW E30 Repair Manual

00-15 · Engine oil service, operation 00 00 249 · PDF pages 22

US 325i / 325is M20 handbook figures. Identify the installed sump and filter, especially on a swapped engine.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.