BMW E34 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / BRAKES

Replace brake pads on factory sliding calipers

Replace pads as an axle set on the illustrated two-guide-bolt calipers, inspect the piston and rotor, and verify a firm pedal before moving.

AdvancedReplacement steps1–3 hours per axleSOURCE-BASED GUIDESource references recorded · technical review pending

Rear brake pads and rotors

1995 U.S. 525i sedan with the factory rear disc and sliding caliper in Bentley.

Tools

  • 7 mm hex bit for the factory capped guide bolts.
  • Caliper hanger, piston press and brake disc micrometer.

Tightening & service specifications

Caliper guide bolt
35 NmClean, dry guide bolts in Bentley’s pad procedure.Bentley · 340-5, pad installation
Rear caliper carrier to trailing arm
67 NmBentley · 340-7, rotor installation and checks
Rotor retaining screw
16 NmBentley · 340-7, rotor installation and checks

BMW catalog parts

1995 525i sedan · rear brake diagram

Replacement steps

Before you start

Bentley 340-4–5 factory floating-caliper design with two capped guide bolts, external anti-rattle clip and an inner pad retained by the piston. Confirm installed front or rear hardware. Use the separate procedure for other calipers and for the rear parking brake.

Estimated time
1–3 hours per axleEditorial estimate for an accessible, source-matching installation.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • Matching axle pad set and sensor as applicable
  • Rated lift and supports
  • Caliper hanger
  • Piston press
  • Torque wrench
  • Rotor micrometer

Check sizes and special fixtures for the installed hardware.

Manual references

010-3–010-4; 340-4–340-5, Figs. 2–6

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • A low reservoir, hydraulic leak, binding piston, damaged guide bolt or soft pedal requires diagnosis. The car must be firmly supported before removing wheels.
  • Keep friction surfaces clean. If a bleed screw or line is opened, use the applicable brake bleeding procedure, including any ASC+T requirements, before moving the car.

Walkthrough

Verify the caliper, rotor and parts

Match both calipers to the illustrated hardware and confirm pads, sensor, retainers and guide bolts. Measure rotors against their marked or verified minimum before deciding to reuse them.

Check: The caliper type is confirmed and both rotors meet the reuse criteria.

Lift, unplug the sensor and release the caliper

Secure the car and remove the axle’s wheels. Remove the guide-bolt caps and bolts. Where fitted, unplug and unclip the wear sensor. Remove the external anti-rattle clip and pull the caliper straight off. Suspend it from the chassis without stressing the hose.

Check: The hose is unstressed, the caliper is secure and no brake pedal operation is possible while it is off.

Inspect and retract the piston

Remove the pads and inspect the caliper, hose, piston boot and guide bolts. Retract the piston slowly using the appropriate tool and the hydraulic procedure for the installed ABS system. Monitor reservoir level and keep dirt out. Stop if the piston binds or leaks.

Check: The piston retracts smoothly and the hydraulic circuit is sealed or has a verified bleeding plan.

Fit the pads and route the sensor

Fit the outer pad and seat the inner pad’s spring in the piston. Renew the sensor if it triggered or was damaged. Route its lead through the original holders. Use approved brake paste only on indicated contact points. The source’s guide bolts are installed clean and dry.

Check: Pads and clips seat correctly, sensor wiring clears moving parts and friction faces are uncontaminated.

Secure the caliper and prove the pedal

For the exact source-shown guide bolts Bentley specifies 35 Nm. Fit the caps and anti-rattle clip, then reassemble both sides and torque wheels to the verified specification. With the car stationary, stroke the pedal to seat the pads and confirm a firm pedal and correct fluid level. Check leaks before a controlled low-speed test and follow the pad maker’s bedding instructions.

Check: Pedal pressure holds, braking is even and no leaks, rubbing or warning remain.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW 5 Series (E34) Service Manual

010-3–010-4; 340-4–340-5, Figs. 2–6 · PDF pages 11, 12, 320, 321

Bentley 340-4–5 factory floating-caliper design with two capped guide bolts, external anti-rattle clip and an inner pad retained by the piston. Confirm installed front or rear hardware. Use the separate procedure for other calipers and for the rear parking brake.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.