BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / DRIVETRAIN

Replace the driveshaft flex disc

Late rear-wheel-drive E30 325i with the original M20B25 and Getrag 260. Match the flange diameter and bolt grade before choosing hardware.

AdvancedReplacement steps2–4 hrSOURCE-BASED GUIDESource references recorded · technical review pending

Replace the driveshaft flex disc

Late rear-wheel-drive E30 325i with the original M20B25 and Getrag 260. Match the flange diameter and bolt grade before choosing hardware.

Tools

  • BMW 26 1 040 for the sliding ring; socket and counterhold for fitted flange bolts. Use 17 mm for standard M10 hex heads when fitted and verify the actual tool fit.
  • Rated exhaust and shaft supports, torque wrench, and a ruler for 4–6 mm preload.

Tightening & service specifications

M10 class 8.8 coupling hardware
48 NmBMW E30 torque manual · 26-1 · PDF 98
M10 class 10.9 coupling hardware
64 NmBMW E30 torque manual · 26-1 · PDF 98
Center mount to body
21 NmBMW E30 torque manual · 26-2 · PDF 99
RWD sliding clamp ring
10 NmBMW E30 torque manual · 26-1 · PDF 98

BMW catalog parts

1991 325i coupe · driveshaft and flex disc diagram

Replacement steps

Before you start

Late rear-wheel-drive E30 325i with the original M20B25 and Getrag 260. Match the flange diameter and bolt grade before choosing hardware.

Estimated time
2–4 hrPlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • BMW 26 1 040 for the sliding ring; socket and counterhold for fitted flange bolts. Use 17 mm for standard M10 hex heads when fitted and verify the actual tool fit.
  • Rated exhaust and shaft supports, torque wrench, and a ruler for 4–6 mm preload.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Flex disc for the fitted flange, matching bolts and new self-locking nuts.

Manual references

26-6 · 26 11 051

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Chock the wheels and use a rated lift or stands. Keep the removed assembly supported separately.
  • Let the exhaust cool. Support the shaft, keep its halves indexed and keep its weight off the fuel crossover line. This guide covers the Getrag 260 layout.

Walkthrough

Expose and support the shaft

Remove the required exhaust sections and heat shields. Mark the flange and shaft orientation. Use BMW 26 1 040 to loosen the sliding joint ring.

Check: The shaft and exhaust are supported with the oxygen sensor lead and fuel lines clear.

Replace the coupling

Release the transmission flange and support bracket. Move the shaft far enough to clear the centering pin without separating its halves. Install the new disc with the molded arrows toward the flange arms.

Check: Every arrow points to the corresponding flange and the bolts retain their specified orientation.

Set preload and torque

Check the centering pilot. Use the torque row for the marked M10 bolt grade. Preload the support 4–6 mm toward the front and tighten its fasteners to 21 Nm. Tighten the fitted RWD sliding ring to 10 Nm after the shaft is installed.

Check: The support is preloaded, the coupling is seated, and the shaft turns freely.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

26-6 · 26 11 051 · PDF pages 459, 460

Late rear-wheel-drive E30 325i with the original M20B25 and Getrag 260. Match the flange diameter and bolt grade before choosing hardware.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.