BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / BRAKES

Front brake pads and discs

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory ventilated front discs and matching sliding calipers; iX hardware differs.

IntermediateReplacement steps1–2 hr per axleSOURCE-BASED GUIDESource references recorded · technical review pending

Front brake pads and discs

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory ventilated front discs and matching sliding calipers; iX hardware differs.

Tools

  • Counterhold wrench on the guide pin. Check the hex on the fitted caliper.
  • Disc micrometer, caliper hanger, rated stands and torque wrench.

Tightening & service specifications

Front disc retaining screw
16 NmBMW E30 torque manual · 34-1 · PDF 136
Front caliper carrier to steering knuckle
123 NmRear-wheel-drive E30 row; BMW specifies lightly oiled bolt threads.BMW E30 torque manual · 34-1 · PDF 136
Front guide-pin bolts
35 NmRenew the bolts for this E30 design.BMW E30 torque manual · 34-1 · PDF 136

BMW catalog parts

1991 325i coupe · front disc diagram

Replacement steps

Before you start

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory ventilated front discs and matching sliding calipers; iX hardware differs.

Estimated time
1–2 hr per axlePlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • Counterhold wrench on the guide pin. Check the hex on the fitted caliper.
  • Disc micrometer, caliper hanger, rated stands and torque wrench.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Matched front pad set and new guide-pin bolts.
  • Two matching discs if the discs are being replaced.

Manual references

34-4 to 34-5 · front pads and discs

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Chock the wheels and support the car on rated stands or a lift before removing a wheel. A jack alone is insufficient.
  • Keep grease off the disc and lining. Support the caliper independently of its hose.
  • Pump the pedal until firm before moving the car. Stop if the pedal sinks, a leak appears or the brakes drag.
  • Check the caliper design first. This sequence covers the bolt-to-guide-pin design with the 35 Nm fastener.

Walkthrough

Check the caliper and disc

Remove the front wheels. Compare the caliper and guide fasteners to BMW’s illustration. Check the disc with a micrometer and confirm the minimum thickness for that disc.

Check: The guide-pin bolt design, pad set and disc match the installed hardware.

Remove the pads

Disconnect the wear sensor if fitted. Counterhold the guide pin while removing the retaining bolt. Hang the caliper and remove the pads.

Check: No tension or twist is on the hose.

Remove or check the disc

For replacement, remove the carrier and disc screw. Clean the hub mating face and check that the new disc sits flat. Tighten the retaining screw to 16 Nm and the carrier bolts to 123 Nm on this RWD application with the factory thread preparation.

Check: The disc sits flat and turns without interference.

Install pads and check pedal

Press the piston back with a spreader while watching reservoir level. Fit the pads and sensor, renew the illustrated guide-pin bolts and tighten them to 35 Nm. Refit the wheels, pump the pedal and check braking at low speed.

Check: The pedal is firm and both front brakes operate normally.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

34-4 to 34-5 · front pads and discs · PDF pages 643, 644

1991 U.S. 325i coupe, M20, rear-wheel drive. Factory ventilated front discs and matching sliding calipers; iX hardware differs.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.