BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / SUSPENSION

Front control arm replacement

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Factory steel wishbones; use the separate procedure for the 325iX or M3.

AdvancedReplacement steps1–2 hr per sideSOURCE-BASED GUIDESource references recorded · technical review pending

Front control arm replacement

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Factory steel wishbones; use the separate procedure for the 325iX or M3.

Have the alignment checked after replacing steering or suspension links. Counting turns is only a starting setting.

Tools

  • BMW 31 1 110 ball joint separator for the standard strut.
  • Torque wrench covering 42–85 Nm. Use the socket that fully fits each replacement nut.

Tightening & service specifications

Inner ball joint to front axle carrier
85 NmBMW E30 torque manual · 31-3 · PDF 104
Outer ball joint to spring strut
65 NmKeep the taper and bore clean and free of grease. Install the locking hardware specified for each joint.BMW E30 torque manual · 31-3 · PDF 104
Control arm bushing bracket to carrier
42 NmBMW E30 torque manual · 31-4 · PDF 105

BMW catalog parts

1991 325i coupe · front wishbone and bushing diagram

Replacement steps

Before you start

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Factory steel wishbones; use the separate procedure for the 325iX or M3.

Estimated time
1–2 hr per sidePlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • BMW 31 1 110 ball joint separator for the standard strut.
  • Torque wrench covering 42–85 Nm. Use the socket that fully fits each replacement nut.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Wishbone for the correct side and its locking hardware.

Manual references

31-6 · front wishbone replacement

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Chock the wheels and support the car on rated stands or a lift before removing a wheel. A jack alone is insufficient.
  • Keep both ball-joint tapers and their seats clean and dry. Fit locking hardware that matches each joint.

Walkthrough

Match the replacement arm

Check the side, steel arm and bushing position against the original. Support the hub so the brake hose cannot be pulled.

Check: The replacement arm, bracket and fasteners match the RWD application.

Release the joints and bracket

Remove the inner and outer joint nuts and separate the tapered joint with the factory separator specified for the strut. Unbolt the rear bushing bracket and withdraw the arm.

Check: The dust boots, hub and hose are clear of the tool path.

Fit the arm and verify steering

Seat the joints and install the specified locking nuts. Tighten the inner joint to 85 Nm, outer joint to 65 Nm and bracket to 42 Nm. Check for full steering travel and arrange an alignment.

Check: The joints are seated, boots intact and alignment checked before normal use.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

31-6 · front wishbone replacement · PDF pages 507

1991 U.S. E30 325i coupe, original rear-wheel-drive front axle. Factory steel wishbones; use the separate procedure for the 325iX or M3.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.