BMW E34 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / ENGINE

Inspect accessory drive belts for wear

Identify the visible belt arrangement and check for glazing, cracking, separation, contamination or poor tracking with the engine off.

BeginnerInspection10–20 minSOURCE-BASED GUIDESource references recorded · technical review pending
Inspection

Before you start

Factory accessory drives on the covered U.S. E34 engines. Bentley groups M20/M30 V-belts separately from M50/M60 poly-ribbed belts. Verify the actual tensioner and routing before any replacement.

Estimated time
10–20 minEditorial estimate for the listed task on accessible original equipment.
Review
Source-based draft · technical review pending

This inspection helps decide the next action. It does not include the resulting repair.

Listed tools & supplies

  • Flashlight
  • Inspection mirror
  • Camera
  • Compatible rib-wear gauge, for an accessible poly-ribbed belt

Check sizes and special fixtures for the installed hardware.

Required parts

  • No replacement part is needed for inspection
Parts to inspect or match separately
  • Replacement belt only after matching the installed routing and accessory drive
  • Tensioner, pulley or leaking component only after diagnosis

Stop the job if

  • Engine or fan could start during the inspection
  • Belt is torn, displaced, frayed or contaminated
  • Access needs a guard removed, tensioner released or the engine turned without the matching procedure

Manual references

020-12 to 020-13, Figs. 9–11

Use these page numbers in your copy of the manual.

Gates TT002-15: inspecting EPDM belt wear ↗

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Engine off, key out and engine cool. Keep hands and tools clear of fans, belts and pinch points.
  • This check is visual. Releasing a tensioner or turning the engine to expose the rest of a belt requires its own procedure.

Inspection steps

Separate the accessory belts from the timing drive

Tools: Flashlight · Camera

Manual 020-12 to 020-13 ↗

Identify the visible belts driving accessories at the front of the engine. Note the narrow V-profile or multiple small ribs, and count the visible belts. The M20 camshaft belt under its cover is outside this inspection.

Check: You have recorded the belt type and the visible route for each accessory belt.

Inspect each accessible span

Tools: Flashlight · Inspection mirror · Camera

Manual 020-13 ↗

Use a light and mirror to inspect the visible faces and edges. Look for polished contact surfaces, cracks, loose strands, separated layers, missing ribs or wet oil. Record which surfaces you could see and which remained hidden.

Check: Photos identify the affected belt, location and type of damage.

Check rib wear on a modern replacement belt

Tools: Compatible rib-wear gauge, for an accessible poly-ribbed belt

Manual 020-13 ↗

EPDM poly-ribbed belts can lose material without obvious cracking. Where the ribs are safely accessible with the engine off, use a compatible belt-wear gauge exactly as its maker instructs. Do not release the tensioner, turn the engine or force access as part of this check. If the belt cannot be measured safely, record that limitation and arrange the proper access procedure.

Check: The record includes the gauge result or clearly says which belt area could not be checked.

Check belt seating and nearby traces

Tools: Flashlight · Inspection mirror

Manual 020-13 ↗

Look for a belt riding at an angle, on a pulley edge or outside its expected grooves. If there is fluid on the belt, look for traces above or beside it from a safe position. Note a reported squeal separately from the visible condition.

Check: The record separates belt condition, seating and any possible leak.

Decide what needs further work

Tools: Camera

Manual 020-13 ↗

A torn, displaced or contaminated belt needs assessment before the engine is run again. Establish the correct routing, belt and tensioning hardware before replacement, and address the source of contamination. Do not use belt dressing to mask a squeal.

Check: The next action accounts for the specific belt and observed fault.

Record your findings

Keep observations and unresolved questions in your private journal before deciding on a repair.

Add to My garage ↗
BMW 5 Series (E34) Service Manual

020-12 to 020-13, Figs. 9–11 · PDF pages 34, 35

Factory accessory drives on the covered U.S. E34 engines. Bentley groups M20/M30 V-belts separately from M50/M60 poly-ribbed belts. Verify the actual tensioner and routing before any replacement.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.