Organize maintenance by the work area
The maintenance chapter separates engine-bay, under-car and body/interior work. Use those work areas to organize an inspection record before choosing the full procedure for the installed engine and equipment.
Keep the car’s observed condition, the source you consulted and the work actually performed as separate entries. My Garage can record service dates, odometer readings, installed parts and the next date or mileage you choose. It does not supply a factory service schedule from this contents page.
Useful details to record
- Installed engine and relevant equipment
- Work date and odometer reading
- Observed condition, source locator and parts used
- Next check chosen from the applicable full schedule
Jobs in this chapter
Open each repair job for linked DIY guides, owner walkthroughs and comments. The locator points to the start of the topic in your service manual.
- Oil service and Inspection I/II schedules020-2 · PDF p. 24Guides & owner fixes
- Service indicator reset and interval tables020-3 · PDF p. 25Guides & owner fixes
- Fluid and lubricant specifications020-8 · PDF p. 30Guides & owner fixes
- Oil and filter change020-9 · PDF p. 31Guides & owner fixes
- Air filter replacement020-10 · PDF p. 32Guides & owner fixes
- Spark plug replacement020-10 · PDF p. 32Guides & owner fixes
- Distributor, ignition leads and fuel filter020-11 · PDF p. 33Guides & owner fixes
- M20 and M30 valve clearance020-11 · PDF p. 33Guides & owner fixes
- Battery, throttle linkage and V-belts020-12 · PDF p. 34Guides & owner fixes
- Poly-ribbed accessory belts020-13 · PDF p. 35Guides & owner fixes
- Cooling system maintenance020-14 · PDF p. 36Guides & owner fixes
- Steering fluid level020-15 · PDF p. 37Guides & owner fixes
- Brake and clutch reservoir020-15 · PDF p. 37Guides & owner fixes
- Oxygen sensor020-15 · PDF p. 37Guides & owner fixes
- Cold tire pressure, rotation and alignment020-16 · PDF p. 38Guides & owner fixes
- Brake lines, pad wear and rotor checks020-16 · PDF p. 38Guides & owner fixes
- Brake fluid renewal and parking brake020-17 · PDF p. 39Guides & owner fixes
- Exhaust and gearbox service020-17 · PDF p. 39Guides & owner fixes
- Suspension, axle boots and fuel line inspection020-18 · PDF p. 40Guides & owner fixes
- Wiper blades020-18 · PDF p. 40Guides & owner fixes
- HVAC microfilter020-19 · PDF p. 41Guides & owner fixes
- Body care, lubrication and seat belts020-19 · PDF p. 41Guides & owner fixes
- Upholstery care020-20 · PDF p. 42Guides & owner fixes
Walkthroughs from these pages
All walkthroughs ↗Plan an M50 coolant-pump job
Check the parts and bleed procedure first, then follow the source-checked mechanical sequence for fan access, pump extraction, seal installation and even tightening.
170-8–170-9, Figs. 12–13; 170-12; 020-13 · planning · source-based guideReplace the engine air filter
Open the factory clip-fastened airbox, replace the element and check the perimeter seal before starting the engine.
020-10, Figs. 5–6 · replacement · source-based guideReplace the front windshield wiper blades
Release the original front blade retainers, seat each replacement and check sweep and park on wet glass.
020-18 and 611-1 to 611-2, Fig. 1 · replacement · source-based guideInspect accessory drive belts for wear
Identify the visible belt arrangement and check for glazing, cracking, separation, contamination or poor tracking with the engine off.
020-12 to 020-13, Figs. 9–11 · inspection · source-based guideCheck the brake and clutch fluid reservoir
Read the brake reservoir level through the wall and document a low or falling level for hydraulic diagnosis.
020-15, Fig. 16; 020-16 · inspection · source-based guideIdentify and check the power-steering fluid
Read the reservoir marking and dipstick on the applicable steering system, then record the level and any evidence of leakage.
020-15, Fig. 15 · inspection · source-based guideCheck and set cold tire pressures
Match the door-pillar placard to your tires and load, measure each wheel cold and track repeat losses.
020-16, tire inflation · inspection · source-based guideChange the oil and cartridge filter on an M50 525i
Drain the engine oil, renew the cartridge and seals, then verify oil pressure, level and leaks before driving.
020-8 to 020-10, Table e and Figs. 3–4 · replacement · source-based guideReplace the M50 or M50TU spark plugs
Remove the individual coils, inspect the plug wells and replace the plugs with a verified set for the installed cylinder head.
020-10–020-11, Table f · replacement · source-based guideReplace the HVAC cabin microfilter
Reach the filter from the glovebox side, remove debris and restore the duct and trim without opening the refrigerant system.
020-19; 513-4; 640-13, Fig. 30 · replacement · source-based guideMeasure brake pad and rotor wear
Check inner and outer pads and compare rotor measurements with the stamped or verified limit for the installed brakes.
020-16; 340-3–340-7, Table b · inspection · source-based guideService the rear differential oil
Confirm an open or limited-slip unit, renew its lubricant and set the level at the correct fill port.
020-8 and 331-4, Fig. 6 · replacement · source-based guideDrawings and component references
Use the OEM catalog to find an assembly under an independent source vehicle selection. Chapter membership does not establish a part’s fitment.
Browse illustrated OEM catalogChapter discussions
No discussions linked to this chapter yet. Ask with the car’s configuration and exact source page so other owners can follow the same reference.