BMW E34 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / ENGINE

Remove and reinstall M50TU single VANOS

Lock crank and cams, remove the actuator, engage the helical gear correctly and prove mechanical timing before startup.

AdvancedReplacement stepsHalf daySOURCE-BASED GUIDESource references recorded · technical review pending
Replacement steps

Before you start

Factory U.S. E34 M50TU single intake VANOS, original timing drive. Use this with 117-18–20 and its figures at the bench. Internal actuator seal replacement is a separate bench operation.

Estimated time
Half dayEditorial estimate for an accessible, source-matching installation.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • BMW 11 2 300 crank pin
  • BMW 11 3 240 camshaft alignment fixture
  • BMW 11 3 390 dummy tensioner
  • E10 socket
  • Low-range torque tools
  • New actuator gasket and applicable seals

Check sizes and special fixtures for the installed hardware.

Manual references

117-18–117-20, Figs. 38–40; 116-3–116-4

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Incorrect cam timing can cause valve-to-piston contact. Stop if the locks will not locate, the chain is slack or the crank resists hand rotation.
  • The primary tensioner plug retains a spring. Use the source order and confirm torques for all fasteners. Bentley’s access-plug metric and imperial values disagree.

Walkthrough

Expose the actuator and set cylinder 1 compression TDC

Isolate the battery and remove coil and cover hardware, oil baffle and the rear studs called out by Bentley. Rotate the crank by hand in its normal direction. Check damper mark and cam lobes, then engage the crank pin and cam blocks.

Check: Both locking tools locate at the same compression TDC without being forced.

Release the secondary sprocket and remove the unit

Disconnect the oil feed and connector, catch the oil and remove the two access plugs. With timing locked, loosen the four E10 sprocket fasteners through the access points. Compress and pin the secondary tensioner as shown in Fig. 39. Remove the housing fasteners and slide the actuator forward. Stop if it will not release without force.

Check: The cam and crank stayed locked, the secondary tensioner is pinned and the unit came away without prying.

Set the installation preload arrangement

Confirm the locks, loose sprocket screws and pinned secondary tensioner. Carefully substitute the dummy primary tensioner and take up slack according to Fig. 40. Clean the mating surface and place the new gasket. Apply the source-specified sealant at the alignment dowels.

Check: The chain has controlled slack and the gasket and dowels are correctly seated.

Engage the first available spline

Bottom the piston cup in its housing. Slide the unit inward to engage the internal splines first. Viewed from the front, turn the secondary sprockets to the clockwise stop. Maintain inward pressure and move them counterclockwise only enough to engage the outer splines, then seat the unit.

Check: The housing seats flush without using the nuts to draw it into engagement.

Set chain preload and secure the timing

Torque the factory housing’s M6 nuts to 10 Nm and its M8 bolt to 22 Nm. Restore the oil feed with fresh seals and tighten its union to 32 Nm. Release the secondary tensioner and set the dummy primary tensioner to Bentley’s 1.3 Nm. Tighten the four sprocket fasteners alternately in the specified 5 Nm and 22 Nm stages for this M50TU.

Check: The housing and sprocket fasteners are secure and the correct preload was used.

Prove timing by hand before reassembly

Remove both locks, turn the crank by hand through at least two full turns and recheck both locks at compression TDC. Stop if either fixture fails to locate. Remove the locks, restore the production tensioner with its piston engaged on the rail and fit the access plugs with verified torque and new seals.

Check: Both locks fit again after rotation, all fixtures are out and the running tensioner is installed.

Restore the cover and check oil feed and operation

Reinstall the oil baffle, cover, coil grounds, breather and wiring. Inspect the feed fitting before and after startup. If the timing or operation is in doubt, repeat the engine-off travel test before putting the car back in service.

Check: There is no fresh leak or new abnormal noise and VANOS operation has a documented check.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW 5 Series (E34) Service Manual

117-18–117-20, Figs. 38–40; 116-3–116-4 · PDF pages 101, 102, 138, 139, 140

Factory U.S. E34 M50TU single intake VANOS, original timing drive. Use this with 117-18–20 and its figures at the bench. Internal actuator seal replacement is a separate bench operation.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.