BMW E34 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / DRIVETRAIN

Drain and refill a factory manual gearbox

Identify the manual gearbox and fluid label, open the fill plug first, then fill and set the level with the car level.

IntermediateReplacement steps45–90 minSOURCE-BASED GUIDESource references recorded · technical review pending

Manual gearbox oil

E34 with the original manual gearbox covered by Bentley. Identify the transmission and fluid label before using a specification.

Open the filler first. Match the listed gearbox code and approved fluid to the installed unit.

Tools

  • 17 mm six-point socket for the external-hex plugs on the factory ATF-filled gearboxes described by Bentley. Verify the actual plug head.
  • Filling hose or pump, drain pan, level supported lift and torque wrench.

Tightening & service specifications

Fill and drain plugs
50 NmBentley’s 250 G, 260 G and 310 Z row.Bentley · 230-2, tightening values
Fill and drain plugs
52 NmBentley’s 560 G six-speed row only.Bentley · 230-2, tightening values
Replacement steps

Before you start

Factory manual boxes in group 230. Fluid designation and torque depend on the observed gearbox and plug. The fluid capacities page lists the source quantities by code.

Estimated time
45–90 minEditorial estimate for an accessible, source-matching installation.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • Verified fluid and plug seals
  • Appropriate plug tools and torque wrench
  • Pump or fill hose
  • Drain pan
  • Level supported lift

Check sizes and special fixtures for the installed hardware.

Manual references

230-1–230-2, Fig. 1

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Confirm the fluid label and current specification before draining. Keep the vehicle level and securely supported. Warm lubricant can burn.

Walkthrough

Match the fluid and plug hardware

Read the gearbox and fluid tags. Identify the side fill plug and lower drain plug from the correct source drawing. Obtain the applicable torque and seals before starting.

Check: The observed transmission, fluid, fill plug and drain plug are all confirmed.

Check fill access first

Clean around both plugs. Break the fill plug loose before opening the drain. If the fill plug will not release or its threads are damaged, resolve that before draining.

Check: The gearbox can be refilled through the intended opening.

Drain and inspect

Drain into a clean pan. Look for excess metal, water or unusual discoloration and record it. Clean the plugs and mating surfaces, then install the drain plug with the correct seal and torque.

Check: The drain is sealed and any unusual debris is documented.

Set the level and check the seals

With the car level, fill slowly through the fill opening until the lubricant reaches the specified opening level. Fit and torque the fill plug. Clean the case, check both plugs for leaks, and recheck after a short drive if the gearbox is otherwise serviceable.

Check: The level, fluid type and applied torque are recorded and both plugs are dry.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW 5 Series (E34) Service Manual

230-1–230-2, Fig. 1 · PDF pages 231, 232

Factory manual boxes in group 230. Fluid designation and torque depend on the observed gearbox and plug. The fluid capacities page lists the source quantities by code.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.