BMW E30 TECHNICAL REFERENCEService manual
Source library
Repair walkthroughs
WORKSHOP GUIDE / ENGINE

M20 timing belt and tensioner

1991 U.S. 325i coupe, M20, rear-wheel drive. Confirm the fitted sprocket profile and matched roller. The M40 procedure is separate.

AdvancedReplacement steps3–5 hrSOURCE-BASED GUIDESource references recorded · technical review pending

M20 timing belt and tensioner

1991 U.S. 325i coupe, M20, rear-wheel drive. Confirm the fitted sprocket profile and matched roller. The M40 procedure is separate.

Use the full M20 procedure for timing and tensioning. Do not move the crank and cam independently with the belt off.

Tools

  • BMW 11 2 150 crankshaft hub holder if the hub is removed. Consult the full procedure before disturbing the hub.
  • 32 mm fan-clutch wrench and pulley holder for the original left-hand coupling.

Tightening & service specifications

M10 camshaft toothed pulley to camshaft
65 NmM20 camshaft pulley only.BMW E30 torque manual · 11-18 · PDF 19
Timing-belt tensioner bolts
16 lb-ft (about 22 Nm)Continental replacement procedure. Tighten in the illustrated order.Continental · M20 timing belt procedure and torque

BMW catalog parts

1991 325i coupe · timing parts diagram

Replacement steps

Before you start

1991 U.S. 325i coupe, M20, rear-wheel drive. Confirm the fitted sprocket profile and matched roller. The M40 procedure is separate.

Estimated time
3–5 hrPlanning estimate for stock hardware in serviceable condition.
Review
Source-based draft · technical review pending

Listed tools & supplies

  • BMW 11 2 150 crankshaft hub holder if the hub is removed. Consult the full procedure before disturbing the hub.
  • 32 mm fan-clutch wrench and pulley holder for the original left-hand coupling.

Check sizes and special fixtures for the installed hardware.

Required parts

  • Matching 127-tooth semicircular belt and tensioner for the late M20B25. Inspect the spring and plunger.

Manual references

11-66a to 11-66b · 11 31 110

Use these page numbers in your copy of the manual.

Process pictures are not indexed for this guide. Use the cited manual’s figures alongside the steps.

Read before working

  • Wait for the engine and coolant to cool completely before opening the system. Catch the coolant and keep it away from children and animals.
  • Keep the crank and cam timed together. Stop if the marks disagree, a sprocket profile is uncertain, or the engine binds by hand.

Walkthrough

Clear the front of the engine

Use the referenced coolant and belt access procedures to remove the radiator, viscous fan, accessory belts, pump pulley, distributor components and timing covers. Retain the crank sensor and damper orientation. If hub removal is needed, use the BMW hub holder and separate tightening procedure.

Check: The cam and crank timing marks are visible.

Set number one to compression TDC

Turn the crankshaft in the normal direction by hand. Verify both marks. Retract the tensioner against its spring and lock it in that position with the bolt indicated in the BMW drawing. Remove the old belt without moving either shaft.

Check: Both marks remain aligned and the late sprockets match the new belt.

Fit and tension the new belt

Route the belt from crank to intermediate shaft to cam, then around the tensioner. Keep slack at the tensioner. Release the roller and rotate the crank slowly through two turns. Verify both marks and tighten the two tensioner bolts to the belt maker’s 16 lb-ft (about 22 Nm), in the specified order.

Check: The marks return to alignment with no binding.

Refit and check

Refit the covers, sensor, distributor and front drive in their original positions. Restore the cooling system and verify that wiring and hoses clear all moving parts before starting.

Check: Coolant is bled, the engine runs smoothly, and the covers and lines are secure.

Repair outcome

Your observations can help the next owner. An outcome report remains owner-reported until reviewed.

BMW E30 Repair Manual

11-66a to 11-66b · 11 31 110 · PDF pages 110, 111

1991 U.S. 325i coupe, M20, rear-wheel drive. Confirm the fitted sprocket profile and matched roller. The M40 procedure is separate.

Source coverage, rights and review status

Owner walkthroughs & comments

Share how the repair went on your car, add a missing detail, or ask a question. Replies stay with the post so the next owner can follow the whole fix.

Loading owner posts…

Owner experience is community advice. Check the vehicle, source and outcome. Sign in to publish, or submit as a guest for review. Photo and video links open on their original sites.